BK FLEX-1K
Rubber-bitumen based, UV-resistant waterproofing material
A polymer-modified bitumen-rubber based, single-component, highly elastic (1000%) waterproofing product. Easily applied by brush, trowel or spray machine, it provides a permanently flexible waterproofing layer.
Πεδία Χρήσης
- On foundations and shear walls
- In wet areas and on retaining walls
- On horizontal and vertical surfaces
- As a repair product on roofs, in concealed gutters and around chimney bases
- In the repair of bituminous membranes
- In the protection and waterproofing of buildings and building elements exposed to seepage water and temporary or permanent water pressure
- In the external waterproofing of water tanks, and in waterproofing over basements and car parks
- Can be used for bonding insulation and drainage boards.
Πλεονεκτήματα
- Easy to prepare and apply.
- A UV-resistant product.
- Provides seamless, monolithic waterproofing.
- Bonds fully to the application surface.
- Has high crack-bridging capability.
- A water-based, environmentally friendly product.
- Can be applied on vertical and horizontal surfaces without sagging.
Συσκευασίες & Προσφορά
In plastic pails, 5-20 kg
Εισαγάγετε ποσότητα για το μέγεθος συσκευασίας που χρειάζεστε και προσθέστε το στη λίστα προσφοράς σας, ώστε το αίτημά σας να δηλώνει εξαρχής την ακριβή συσκευασία.
| Συσκευασία | Ποσ. | |
|---|---|---|
| 5 kg plastik kova | ||
| 20 kg plastik kova |
| Κατανάλωση | Total theoretical consumption is 1.50-2.00 kg/m². |
|---|---|
| Διάρκεια Ζωής | Can be stored for 12 months in its unopened original packaging in dry environments at temperatures between +5°C and +25°C. Opened packages must be used immediately. |
Εφαρμογή
Surface preparation: The application surface must be sound, dry, clean and free of loose particles. Sharp points and edges on the surface should be rounded off with an angle grinder and deep voids filled with repair mortar. Internal corners and wall junctions should be chamfered. The application surface should be primed with a solvent-free bitumen primer, and application should begin only after the primer has dried completely. Surfaces that would reduce the adhesion of the material should be roughened. Priming: The product can be used as a primer diluted with water at a ratio of 1/5. The material should be spread evenly with a suitable brush, without allowing material to accumulate on horizontal surfaces. Allow the primer to dry and then proceed with the main application. A consumption of 0.25 kg/m² is recommended. Application: Apply at least 2 coats to the prepared surface by brush, trowel or spray. After the first coat has been applied, it must be fully dry before the second coat is applied. The second coat should be applied perpendicular to the first. Application tools: roller or brush.
Τεχνικά Χαρακτηριστικά
| BİLEŞİM | Polimer Modifiye Bitüm Kauçuk |
|---|---|
| RENK | Siyah |
| YOĞUNLUK (A / A+B) | 1,20 kg/l |
| KARIŞIM ORANI (A+B) | 30 kg |
| KATI MADDE (A / A+B) | 70% |
| UYGULAMA SICAKLIĞI | +5°C 35°C |
| SERVİS SICAKLIĞI | -20°C 80°C |
| TAM KURUMA | 1-5 Gün |
| SU GEÇİRİMSİZLİK (EN 15820) | W2B (Süre: 72 saat, Basınç: 0,75 Bar, kuru film kalınlığı ≥ 3 mm, filesiz) |
| ÇATLAK KÖPRÜLEME (EN 15812) | CB2 (Köprülenen Çatlak: ≥ 2 mm) |
| DÜŞÜK SICAKLIKTA ESNEKLİK (EN 15813) | Geçer (Süre: 1 saat, Sıcaklık: 0°C, Yöntem: 3 sn'de bükme) |
| YÜKSEK SICAKLIKTA BOYUTSAL KARARLILIK (EN 15818) | Geçer (Süre: 2 saat, Sıcaklık: 70°C) |
| SU DİRENCİ (EN 15817) | Geçer (28 gün suda bekletme) |
| YAĞMUR DİRENCİ (EN 15816) | R1 (uygulamadan 8 saat sonra yağmurlama yapılır) |
| KATMAN KALINLIĞINDA AZALMA (EN 15819) | Geçer (%50'den az olmalıdır) |
| YANGIN SINIFI (EN 13501-1) | Euroclass E |
| KOPMA UZAMASI (ISO 37, MIL-STD-810G) | 1000% |
Επικοινωνήστε μαζί μας για τιμή & προσφορά
Προσθέστε τα προϊόντα και τις συσκευασίες που χρειάζεστε στη λίστα προσφοράς ή επικοινωνήστε απευθείας μαζί μας.